| CAS No.: | 38891-59-7 |
|---|---|
| Formula: | C15h16o2`C2h7on`C3h5ocl |
| EINECS: | 500-003-5 |
| Samples: |
|---|
| Customization: |
|---|
|
Shipping Cost:
Estimated freight per unit. |
about shipping cost and estimated delivery time. |
|---|
| Payment Method: |
|
|---|---|
| Initial Payment Full Payment |
| Currency: | US$ |
|---|
| Return&refunds: | You can apply for a refund up to 30 days after receipt of the products. |
|---|
Suppliers with verified business licenses
Audited Supplier
The wear-resistant ceramic adhesive is room temperature or heat curing epoxy adhesive. It is applied in all kinds of metal, plastic, glass steel, porcelain, comment concrete, wood, and other material's bonding.
It can withstand -40ºC~ 150ºC, can be widely used in the bonding of various ceramic sheets and metals under the conditions of 150ºC or less. For long-term use should be below 100ºC.
| Test Item (Unit) | Test Measure (Condition) | Component A | Component B |
| Color | / |
White to rice white uniform colloid |
Rice white to beige uniform colloid |
| Density (g/cm3) | Hydrometer Jar (25ºC) | 1.60±0.10 | 1.50±0.10 |
| Viscosity (pa·s) | Rheologic (25ºC) | Past (90~115) | Paste (14~70) |
| Working time (min) | Mixing 100g (25ºC) | 15±3 | |
| Dry time (min) | Mixed thin layer (25ºC) | 60±15 | |
| Hardness (D) | Hardness blocks (25ºC) | 80±5 | |
| Nonvolatile content (%) | 125ºC @ 180min | ≥99.0 | |
| Test Item (Unit) | Bonding material | Curing Condition | Test Condition | Performance |
|
Tensile shear Strength (Mpa) |
45#steel/45#steel | 23ºC for 24h | 23ºC 5mm/min | ≥20.0 |
| 23ºC for 72h | 23ºC 5mm/min | ≥22.0 | ||
|
Tensile shear Strength (Mpa) |
Aviation aluminum/ Aviation aluminum |
23ºC for 72h | 23ºC 5mm/min | ≥12.0 |
| Impact strength (KJ/m2) | Sample preparation | 23ºC for 72h | 23ºC 2J | ≥4.0 |
1. Mixing ration: A:B = 1:4 (weight ratio)
2. Adhesive surface keep dry, clean, no oil. If the surface is smooth, we need to be properly polished.
3. According to proportionate, mixing A and B parts. Stir well after coating.
4. To reach the highest intensity. Constant temperature and humidity curing ≥ 72 hours
Precautions
1. With the glue should be properly in accordance with the proportion of the two components were weighed, do not make too much of any one part, to avoid the strength reduction, curing is not complete.
2. Must be uniform when mixed and used within 8 minutes. If the temperature is low, with less plastic, the use of a corresponding increase in time. High temperature, with a large amount of plastic, it should spread plastic compound to extend the use of time.
3. Must be sealed tightly after using A, B two part to avoid affecting the product's absorbent and bonding strength.
4. If your hand has the excess glue, please clean by alcohol before curing.
5. Prevent contact with children.
6. Detailed safety instructions can be found in the MSDS.
5kg/set, 1 barrel of each component for a set.
4kg/barrel for Component A; 1kg/barrel for Component B. Each set apply for 2 - 3 m2
Storage
1. Please seal A, B at room temperature, two years warranty.
2. This product from the packaging of the pouring out of the glue once, can not be poured back to A or B components.
3. This product is non-flammable, should be placed in a cool, dry place storage.
Suppliers with verified business licenses
Audited Supplier 
){kind=link}
){kind=link}